The thermostat’s location can significantly impact how comfortable the house is, how Long The HVAC System Runs, and how much it costs to run. Therefore, you might consider moving the thermostat to a different room. By fusing your most recent research with knowledge of the industry, this post will respond to your question.
Also check: Lennox Vs Goodman Air Conditioner: Which Is Right for You?
How to Move a Thermostat
Follow these steps to relocate the thermostat to another room
- Move the thermostat to a new location.
- Deactivate the thermostat
- Take out the thermostat
- Connect the cable to a new location.
- Move the thermostat to a new location.
- Restart the thermostat
- Repair the old thermostat’s location
1. Move the thermostat to a new location.
The thermostat’s placement in the house is critical. When turned on and off, the furnace or air conditioner is controlled by this device. The temperature of the environment where a thermostat is installed is typically the only temperature it can detect. This means that regardless of whether you are home, the thermostat will turn off automatically when the set temperature is reached. To reflect the home’s average temperature, the thermostat should be installed in a prominent location. Place the thermostat outside, directly above duct registers, close to hot appliances, and away from windows, draughts, and direct sunlight-a remote area without heating or cooling. Avoid setting the thermostat in a location where the temperature is noticeably higher than the average for the house.
2. Deactivate the thermostat
Turning off the power before touching or messing with wires is crucial when working with electronic devices. Electrocution is extremely risky and potentially fatal (although thermostats do not require much power). The thermostat in the fuse box is typically off. The thermostat will be connected to a breaker, so shut it off. Afterward, turn the thermostat back on to ensure you picked the correct breaker. The thermostat doesn’t need to be on; it’s okay. WARNING: If you are unsure of your ability to turn off the thermostat, do not attempt this project. Contact an electrician or HVAC expert for advice if you need it regarding any of the following steps.
3. Take out the thermostat
You can take the thermostat out after turning off the power. Usually, a couple of screws need to be loosened. This makes it simple for you to take the device out. The thermostat is still connected to the wall by a wire. Before continuing, take a close-up picture of the thermostat wiring. When wiring the thermostat in a new location, this is necessary. With your finger or pliers, untie the wire at this time. The fact that each wire typically has a distinct color makes rewiring much simpler. Remove the housings for the two thermostat brackets. And during this process, the thermostat surface. To leave nothing behind on the wall is your goal.
4. Connect the cable to a new location.
It’s time to relocate those wires right now. Depending on how far you want to move your thermostat, this step’s difficulty varies greatly. For instance, the task is straightforward if you only need to move the thermostat to the opposite side of the wall. Moving the thermostat around the house is much more difficult. You should hire an electrician for long thermostat moves that look the most professional.
5. Move the thermostat to a new location.
No matter how far you move the thermostat, reconnect the wire in its original position after setting it up in a new location. Reattach the thermostat to the wall using the screws removed from the previous location.
I. Switch the thermostat to the opposite wall’s position.
The thermostat can be installed on the opposite side of the wall without extending the wire. It makes the task much more accessible. Drill a hole in the wall behind the new thermostat’s location to start. Next, insert a wire fishing tool through the fresh hole. Depending on the type, it is advised to install the thermostat housing either before or after removing the wire.
II. Move the thermostat over a long distance
If you need to run the thermostat over a large area, the wiring needs to be smarter and more inventive. The simplest solution is to return the wire to the new thermostat by running it along the exterior wall in the upper corner of the house. Another option is to run cables through the crawl space, basement, or attic. For each option, a reliable electric splice and wire gauges must be suited to the distance.
You must also know where to drill holes in the ceiling or floor when running wires through an attic or crawl space. If you do this, you can hit the wall cavity or directly in front of the wall for a more straightforward option. Fires, malfunctioning thermostats, and other electrical problems can all be caused by improperly managed electrical wiring.
6. Turn the thermostat back on.
When connecting the thermostat to a new location, you’ve reached the crunch point. Before resetting the thermostat, ensure all wiring connections are made correctly. It’s fine if the thermostat keeps operating normally. However, seek professional assistance or double-check your work if you immediately flip the breaker or don’t see the thermostat feature.
7. Make the old thermostat’s location better.
Lastly, fill in the holes in the old thermostat. The holes are often so small that they can be painted over and repaired like new using drywall putty. However, the drywall might need to be patched if the holes are too big for the drywall filler. We suggest you fix this hole as soon as you can. The longer you wait, the more likely you’ll put off doing something on your to-do list and sit in the backseat. The house’s comfort and resale value are affected by even minor scratches.
Also check: How Long Should A Heat Pump Run Per Day?
Change your thermostat’s position to where it performs the best!
A thermostat that alternately turns on and off is the most annoying thing ever. Perhaps, your thermostat needs to be changed. I believe in this article; I’ve shown you how to choose the best location for your thermostat and how to move it.
